UV-C Disinfection in Food Processing: Rooms, Cold Stores, Packaging
· 7 min read
Food plants clean and sanitise every day, yet surfaces are recontaminated between cleaning cycles. UV-C fixtures can cut the microbial load on exposed surfaces during breaks and overnight, without chemicals or residues. This article covers where UV-C works in a food plant, where it doesn’t, and how to plan a room system.
What UV-C can and can’t do
UV-C supports a hygiene programme; it does not replace cleaning. Keep three limits in mind:
- It only works on surfaces it can see. UV-C travels in straight lines, so shadows behind equipment, inside crevices and under conveyors receive little or no dose.
- Dirt shields microorganisms. Fat, protein and dust absorb UV-C. Surfaces must be clean for UV-C to reach what remains on them.
- It works on the surface only. UV-C does not penetrate into materials. Treating food itself is regulated separately in many countries and is not covered here.
Where UV-C fits in a food plant
| Area | Typical targets | Design notes |
|---|---|---|
| Processing rooms | Listeria, Salmonella, general surface bacteria | Run during breaks and overnight when no one is present; aim at work surfaces and floors |
| Cold stores and chillers | Mould spores, Listeria | Cold air reduces lamp output; mould needs much higher doses than bacteria |
| Packaging areas | Mould and bacteria on conveyors, tables and packaging material | Many shadows from equipment; several fixture angles help |
| Air-handling units serving the plant | Biofilm and mould on cooling coils | Sized like any HVAC coil system |
Listeria monocytogenes deserves particular attention because it can grow at refrigeration temperatures and persists in cold, wet environments such as chillers, drains and processing rooms.
Planning a room system
A room design needs the following inputs:
- Room length, width and height.
- The height of the work surface to protect, often around 0.9 m.
- Fixture positions, mounting height, orientation and the number of lamps per fixture.
- The lamp model, which sets UV-C output and lamp length.
- How reflective the walls and ceiling are. Stainless steel and white panels reflect differently, and both reflect UV-C far less than they reflect visible light.
- The target organism, log reduction and a safety factor.
The result that matters is the cycle time: how long the fixtures must run for the weakest-lit point on the work surface to reach the target dose. See UV-C dose and D90 values for how that dose is set.
Example: an 8 × 5 m processing room
Consider a room 8 m long, 5 m wide and 3 m high with four ceiling fixtures, each fitted with two 36 W lamps. The goal is a 3-log (99.9 %) reduction of Listeria on a 0.9 m work surface, with a safety factor of 2.
- Target dose: 3 × 3.5 mJ/cm² × 2 = 21 mJ/cm².
- Weakest point on the work surface: about 48 µW/cm² (0.048 mW/cm²).
- Cycle time: 21 ÷ 0.048 ≈ 435 seconds, about 7 minutes.
If the same room had a mould problem, the dose for Aspergillus niger spores would be roughly 30 times higher, and the cycle would run for hours. That would call for more fixtures or a longer unoccupied period.
Cold stores need extra margin
Standard low-pressure lamps give much less UV-C in cold, moving air than their catalogue rating. In chillers and freezers, apply the manufacturer’s temperature derating, consider amalgam lamps, which hold their output better, or use fixtures with protective sleeves. See why UV-C lamps lose output in cold air.
Keeping people safe
UV-C harms skin and eyes, so room systems must only run when the space is empty:
- door interlocks and occupancy sensors that switch the lamps off when someone enters;
- timers that run cycles during breaks and after cleaning;
- warning lights and signs at every entrance;
- a check of exposure at eye level wherever people could be present while lamps are on.
UV-C also degrades some plastics, rubber seals and printed labels over time, so check what sits in direct view of the fixtures. Our UV-C safety guide covers exposure limits in detail.
Proving it works
Record the design dose and cycle time, then verify on site. UV-C indicator cards or a radiometer confirm the dose reaching critical points, and swab or ATP tests before and after a cycle show the effect on real surfaces. A design report that shows fixture positions, the irradiance across the work surface and the resulting cycle time gives auditors a clear basis for these checks.