UV-C for HVAC Cooling Coils: How It Works and How to Size It
· 7 min read
A cooling coil is wet, dark and constantly fed with dust from the airstream. That makes it one of the best places in a building for biofilm and mould to grow. UV-C lamps mounted next to the coil irradiate its surface around the clock and stop that growth before it starts. This article explains how coil UV-C works, what decides how many lamps you need, and how to document the result.
Why cooling coils need disinfection
When air is cooled below its dew point, water condenses on the fins. Combined with organic dust that gets past the filters, this film feeds bacteria and mould. Over time it builds into biofilm, which:
- insulates the fins and reduces heat transfer, so the coil cools less for the same energy;
- narrows the air passages and raises the pressure drop across the coil, so fans work harder;
- can release spores and odours into the supply air;
- makes mechanical and chemical coil cleaning more frequent and more difficult.
UV-C does not clean a coil that is already heavily fouled. It is a way of keeping a clean coil clean, so start a UV-C installation with a thoroughly cleaned coil.
How UV-C inactivates microorganisms
Germicidal lamps are usually low-pressure mercury lamps that emit most of their energy at 253.7 nm, in the UV-C band. Radiation at this wavelength damages the DNA and RNA of bacteria, moulds and viruses so they can no longer reproduce. What matters is the dose, the energy received per unit area:
dose (mJ/cm²) = irradiance (mW/cm²) × exposure time (s)
This is where coils differ from almost every other UV-C application. A coil is irradiated continuously, 24 hours a day, so even a modest irradiance adds up to a very large daily dose. Moving air is different: it passes the lamps in a fraction of a second. The dose and D90 guide explains how dose translates into kill rates for specific organisms.
Coil surface or airstream?
Coil UV-C systems are designed for one of two goals, and they are sized differently.
| Goal | Exposure time | What drives the design |
|---|---|---|
| Keep the coil surface clean | Continuous | The lowest irradiance anywhere on the coil face, and the time it needs to reach the target dose |
| Inactivate microorganisms in the air | A fraction of a second per pass | Average irradiance across the duct, air velocity, and the length of the irradiated zone |
Most coil installations target the surface. Single-pass reductions in the airstream are usually modest at normal duct velocities, but they add up over repeated passes in a recirculating system.
What decides the number of lamps
- Coil size. Width and height set the area to cover. Lamps usually run across the coil width, spaced evenly over its height.
- Lamp model. UV-C output in watts and arc length determine how much radiation reaches each part of the coil.
- Distance to the coil. Closer lamps give higher but less even irradiance. Further away, the light spreads more evenly but weakens.
- Position. Lamps are often mounted on the leaving-air side, where the coil and drain pan are wettest.
- Target organism and log reduction. Mould spores need far more dose than bacteria, so the organism you choose can change the design by an order of magnitude.
- Derating. Lamps lose output with age, in cold moving air and when dirty. See why UV-C lamps lose output in cold air.
- Reflections. Reflective casing walls add to the irradiance; painted or dirty surfaces add little.
A worked example
Take a coil 1.22 m wide and 0.91 m high. The goal is a 99.9 % (3-log) reduction of Aspergillus niger spores, one of the more UV-resistant common moulds, with a representative D90 of about 100 mJ/cm². The target dose is therefore 3 × 100 = 300 mJ/cm².
- If the weakest point on the coil face receives 1,000 µW/cm² (1 mW/cm²) after derating, the time to reach 300 mJ/cm² is 300 seconds, or 5 minutes.
- If the weakest point receives only 200 µW/cm², the same target takes 25 minutes.
Both designs reach the target many times a day, because the coil is never switched off. The practical lesson is that the weakest spot decides the design. Corners and edges receive much less than the centre of the coil, so check the minimum irradiance, not only the average.
Practical checklist
- Use ozone-free lamps, which block the 185 nm line that produces ozone.
- Shield plastics, gaskets, cable insulation and filter media from direct UV-C, which degrades them.
- Fit door interlocks so the lamps switch off when the unit is opened. See UV-C safety.
- Replace lamps by operating hours, not by appearance. A lamp rated for 9,000 hours reaches that in about a year of continuous running, and it still glows blue long after its UV-C output has dropped.
- Clean lamps when the coil is serviced, since dust on the glass blocks UV-C.
Standards and documentation
ASHRAE publishes test methods for UV-C devices in air handlers: Standard 185.1 for airstream inactivation and Standard 185.2 for irradiated surfaces such as coils. For a specific installation, building owners and auditors increasingly expect a written design that shows lamp positions, the irradiance across the coil, and the time to reach the target. A report with these graphs, tied to the specific unit, answers that question before it is asked.